Free · hydrogen · no sign-up

Electrolysis calculator

How much hydrogen does an electrolyser produce, at what efficiency and at what cost? And how much of its waste heat can a district heating network take? Enter power, technology and prices.

Electrolyser

Costs

Waste heat into the heating network

Levelised cost of hydrogen depending on full-load hours at the same power price. Few hours make hydrogen expensive because the investment is spread over a small quantity. Dot: your input.
with heat revenuewithout waste heat use

No warranty: rough calculation with simplified models and your assumptions. It does not replace a design, a quotation or a project feasibility study. Checking and using the results is the responsibility of the user.

Next step

Integrate the waste heat into the network?

In the heat balance tool you calculate the heat pump that lifts the waste heat to network temperature, with real refrigerant data and several load cases.

Open the heat pump example

How the electrolysis calculator works

An electrolyser splits water into hydrogen and oxygen using electricity. How much hydrogen comes from one megawatt hour is given by the specific consumption of the whole system in kWh per kg, i.e. stacks plus rectifier, water treatment, gas purification, cooling and auxiliary drives (balance of plant). One kilogram of hydrogen contains 33.3 kWh (lower heating value) or 39.4 kWh (higher heating value).

1. Efficiency and waste heat

The efficiency relative to the lower heating value is 33.3 kWh/kg divided by the specific consumption. Most of the remaining power becomes heat in the cooling circuit, usually around 55 to 65 °C for PEM and AEM plants and around 70 to 80 °C for alkaline plants. Part of it can be used; for a district heating network with 90 °C flow, a heat pump has to raise the temperature. The calculator estimates its COP conservatively from the Carnot cycle between condensation just above the network flow and evaporation just below the cooled waste heat (10 K cooling, 3 K approach each). For the heat pump alone there is the large heat pump calculator.

2. Levelised cost of hydrogen

Power per kg plus capital (annuity of the investment after subsidy) and operation, spread over the quantity produced, minus the revenue for the waste heat after deducting the heat pump power. Stack replacement, degradation, compression, storage and transport are not included.

3. Water demand

Chemically, just under 9 litres of water are consumed per kg of hydrogen. With treatment (reverse osmosis, ion exchange) and blowdown, a plant needs considerably more depending on the raw water; with evaporative coolers, cooling comes on top.

Frequently asked questions

How efficient is hydrogen electrolysis?

Relative to the lower heating value, today’s PEM and alkaline systems reach about 60 to 65 % (around 50 to 55 kWh of power per kg of hydrogen). High-temperature electrolysis (SOEC) needs considerably less power per kg using steam from waste heat.

How much hydrogen does a 10 MW electrolyser produce?

At 55 kWh/kg around 180 kg per hour, so at 4,000 full-load hours about 730 tonnes per year.

What is the difference between PEM and AEL?

PEM electrolysers use a polymer membrane, are compact and follow load changes quickly, but need precious metals. Alkaline electrolysers (AEL) use potassium hydroxide, are proven and cheaper per kW, but react more slowly and need a minimum load.

Is the electrolyser’s waste heat worthwhile for district heating?

Around a third of the power becomes heat. At temperatures around 60 °C a heat pump is usually needed; then the heat revenue noticeably lowers the hydrogen cost if the network is nearby and takes the heat over many hours.

What does the calculator cost?

Nothing. It is free to use without sign-up.

← All free calculators

Transparency

How we calculate

  • Water and steam to IAPWS-IF97 – the industry standard for power plant and process calculations
  • Refrigerants with CoolProp – Helmholtz reference equations, open and verifiable
  • Steady-state mass, energy and pressure balance, solved iteratively until nothing changes any more (10⁻⁷)
  • All formulas, assumptions and limits openly documented – automated tests against reference values with every change
See the calculation basis